Poll Service (bacnet-BacnetMultiPoll)

This component configures and manages a group of BACnet proxy points to be polled. Each BACnet network port (Ip Port, EthernetPort, MstpPort, ScPort and ScHubPort) provides its own PollService with three polling rates (Fast, Normal, and Slow). This varies from other network drivers that use a single PollService.

In addition to the three rates of speed (fast, normal, and slow), a fourth speed refers to the dibs stack. When a point is subscribed, it immediately gets first dibs and goes to the top of the dibs stack. The poll scheduler always polls the dibs before doing anything else using last-in, first-out (LIFO). This means that as long as entries are in the dibs stack, the driver polls them as fast as possible with no artificial delays.

When the dibs stack is empty, the scheduler attempts to poll the components using an algorithm designed to create uniform network traffic. For example, if the

Sets the target polling interval for devices that can be polled (they are pollable) and assigned to the Fast Rate group.

is configured to 5000 ms and five components are currently subscribed at this speed, the scheduler attempts to poll each component with a second of delay.

Every ten seconds the poll scheduler rechecks the speeds for configuration changes. This means that if you change a point’s configuration from slow to fast, it takes at most ten seconds for the change to take effect.

The driver updates statistics every ten seconds. You may manually reset statistics using the reset statistics action.

Figure 59. Poll Service properties

You access these properties by expanding Config > Drivers, the BACnet network Bacnet Comm > Network followed by expanding a port (Ip Port, EthernetPort or MstpPort) and double-clicking the Poll Service node.

Property	Value	Description
Poll Enabled	`true` (default) or `false`	Determines user control over polling. `true` enables a system user to use the Live Updates (play) button in History views to poll for live data for the associated imported history(ies). `false` renders this button unavailable in history views for the associated imported history(ies).
Fast Rate	hours minutes seconds (defaults to 1 second)	Sets the target polling interval for devices that can be polled (they are pollable) and assigned to the Fast Rate group.
Normal Rate	hours minutes seconds (defaults to 5 seconds)	Sets the target polling interval for devices that can be polled (they are pollable) and assigned to the Fast Rate group.
Slow Rate	hours minutes seconds (defaults to 30 seconds)	Sets the target polling interval for devices that can be polled (they are pollable) and assigned to the Fast Rate group.
Statistics Start	read-only timestamp	Reports either the last manual reset of poll statistics or, if statistics have not been reset, the first steady state time immediately following the last station restart.
Average Poll	read-only	Reports the average time spent during each poll event. This does not relate to the total time required to complete a poll cycle for any of the three rates. It is the time spent polling a given group of objects before pausing and switching to another group either using the same or a different poll rate.
Busy Time	read-only	Displays a percentage of time spent by the poll thread actually polling points using all poll rates. Includes (in parentheses) the ratio of time spent polling/total time since statistics were restarted. Given a small amount of time is spent transitioning among poll rates, and with the thread sleeping to evenly space out polling messages, it is unlikely to ever see `Busy Time` reach exactly 100%. However, any percentage above 95% indicates that the poll thread is basically spending all of its time actually polling. NOTE: In the case of the Poll Service for a BACnet network port, because two threads are used for polling, it is possible to see a `Busy Time` approaching 200%. In this case, divide `Busy Time` in half to get an average busy time for each thread.
Total Polls	read only	Reports the total number of polls conducted and the time spent waiting for polls to execute. This time is the same time indicated in the ratio of the `Busy Time` property. Typically, the total poll count indicates the number of times the PollService polled any object. It is not a running total of the actual poll cycles.
Dibs Polls	read-only	Reports the percentage and ratio of the number of DIBS polls versus total polls.
Fast Polls	read-only	Reports the number of polls made processing the fast queue.
Normal Polls	read-only	Reports the number of polls made processing the normal queue.
Slow Polls	read-only	Reports the number of polls made processing the slow queue.
Dibs Count	read-only	Reports the current and average number of components in the DIBS stack. (DIBS stands for Distributed Internet Backup System).
Fast Count	read-only	Reports the current and average number of components in the fast queue.
Normal Count	read-only	Reports the current and average number of components in the normal queue.
Slow Count	read-only	Reports the current and average number of components in the slow queue.
Fast Cycle Time	read-only	Reports the average cycle time for the fast queue.
Normal Cycle Time	read-only	Reports the average cycle time for the normal queue.
Slow Cycle Time	read-only	Reports the average cycle time for the slow queue.
Point Count	read-only	Reports the current and average number of points being polled.
Object Count	read-only	Reports the current and average number of objects being polled.
Virtual Count	read-only	Reports the virtual count of points and objects being polled.
Number of Threads	read-only	Reports the total number of polling threads.

Actions

Enable starts polling.
Disable suspends polling.
Reset Statistics manually retrieves fresh statistics.
Rebuild Poll Lists